>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> Repair GDFS
Bookmark topic
Also be sure that battery is not empty and try to set lower speed of connection phone to pc
--
Posted: 2008-05-23 14:49:02
Edit :
Quote
Or try a service cable like cruiser... using COM port and externall battery to revive the phone from the dead... reparing damaged GDFS without backup on db2020 phone like your k800 can be found on
www.topsony.com on the english forum...
--
Posted: 2008-05-23 17:00:40
Edit :
Quote
@Malex
You've done it before and it works. Maybe I'm not doing it right, or I use wrong tool.
OK.. for the first step...
I have :
- SEtool2 lite
- DCU-60
- EROM file
- GDFS Backup
- Main Firmware+FS
My phone is K800
The problem is SEtool2 lite does not detect my phone by holding 'C'.
I Put GDFS Backup in misc window and holding 2+5 then write GDFS i got 'phoneid error 1, Phone info read error !' in the log.
My question :
Is your phone is DB 2020 ?
Did you use SEtool2 lite or SEtool full version ?
Did you use DCU-60 or service cable ?
--
Posted: 2008-05-24 09:30:04
Edit :
Quote
Maybe idiot from me, but is it a possibility restore your fone with pay-serv like DAVINCI or WOTAN are you try ?
Go in they're forum and ask if it is possible.
Sorry if i m wrong but i only want to help you.
--
Posted: 2008-05-24 20:51:14
Edit :
Quote
I have k800(db2020 phone) setool lite. You should start your flashing with flashing main(holding 2+5 of course) and only then gdfs. Other order won't work.
--
Posted: 2008-05-24 22:56:24
Edit :
Quote
I used dcu60 cable
--
Posted: 2008-05-24 22:59:36
Edit :
Quote
try to charge ur battery outside ur phone using any charger untill full and then try to reconnect...
_________________
K800i black--> K810 R8BA+hpm 70+1gb m2 sandisk+lot off patches.
[ This Message was edited by: alfath on 2008-05-25 19:44 ]
--
Posted: 2008-05-25 20:43:46
Edit :
Quote
did you install usb drivers first???if it doesnt have red light blinking in infrared you dont have to hold 2+5...and in flashing you must hold c...
--
Posted: 2008-05-27 19:01:49
Edit :
Quote
OK, this what I've tried.
I've backup the original GDFS
All driver needed is installed.
Batt is fully charge using my friend's phone (W830).
Try to flash using SEtool2 lite (hold c while connect) ==> not detected
Try to flash and write GDFS using SEtool2 lite (hold 2+5 while connect) ==> got this log :
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601230700 CERT:N/A
phoneid error 1
Error during phone id.
Elapsed:18 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601230700 CERT:N/A
phoneid error 1
Phone info read error !
Elapsed:36 secs.
Try to flash using XS++ 3.1 (hold c while connect) ==> not detected
Try to flash using XS++ 3.1 (hold 2+5 while connect) ==> got this log :
00:27:39| XS++ v3.1 (Darwin) Ready !
00:27:39| Executed on Microsoft Windows XP
00:27:45|
00:27:45| Attempting to open the interface...
00:27:45|
00:27:45| TURN OFF PHONE!
00:27:45| Hold 'C' button on phone and connect phone NOW.
00:27:45| You have 30 seconds...
00:27:45|
00:28:04| Baseband ID: 9900
00:28:04| Protocol Version: 3.1
00:29:56| Cannot open ŒýC
00:29:56| Sendinging shutdown signal to phone...
00:29:58| Shutting down..
Still no luck. I think I'm gonna give a rest for a day or two then try it again...
I'll post the result...
Meanwhile all suggestion is very much accepted.
Thanks for your help guys..!!
You are all wonderful...
[ This Message was edited by: opexblue on 2008-05-28 12:44 ]
[ This Message was edited by: opexblue on 2008-05-28 12:50 ]
--
Posted: 2008-05-28 13:38:21
Edit :
Quote
You're welcome
Try to flash your main first holding 2+5
--
Posted: 2008-05-28 16:53:23
Edit :
Quote
New Topic
Reply
