>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Technical
> T610 Modem settings
Bookmark topic
Hi Folks
I assume that you have already gone to the Prefs->Bluetooth menu and done a ADD device and have that sync.
You next need to do the following below...
Some comments. I got my Clie NZ90 to work with BlueTooth and T610.
You need to Prefs->Connections->Sony BT to GSM.
Then click edit, then click on the Device.
The Clie will initiate a search for the T610 (which needs to have its BT turned on). Once found, the modem will work.
I believe the Sony BT to GSM needs to tie to a particular phone type, that's why the additional step...not exactly user friendly on the Clie.
Rgds
--
Posted: 2003-06-30 05:54:26
Edit :
Quote
Thank you for your sharing rufidorsa.
But problem still cannot solve.
Which GSM provider you are using ?
in HK ?
what number you dial ?
*99***1# is what i use as CID on T610 Sunday_GPRS use CID 1.
Still getting error : Serial:line error (0x0306)
--
Posted: 2003-07-02 07:11:42
Edit :
Quote
Quote:
On 2003-06-07 08:12:17, ZA wrote:
....And the same T610 would respond to dialing over Bluetooth from a Tungsten T and my ....
What settings did you use on the Tungsten T under preferences / communication/connection? I tried the T68 and 'gsm phone' both did not work, while the Tunsten could dial trough a Siemens S55.
Thanks in advance
--
Posted: 2003-07-10 23:18:41
Edit :
Quote
Hi just use the hide phone function in your T610 and connect with NX70. You will connect to the network
I try use MobileSMS and Pocketlink and have no problem~
Cheers
--
Posted: 2003-07-18 07:47:05
Edit :
Quote
I have not tried to use BT to connect gprs but I am writing the infrared connection settings, maybe it will help.
T610 - Ipaq infrared gprs connection
T610 side:
First make sure that you gprs settings are working and you are able to browse wap sites using your phone. Then;
menu > connectivity > data comm. > data accounts > new account > select gprs data > type "net" as the name of connection > for APN name type "internet" > leave blank both "username" and "password" > save the setting > select the "net" account from the menu and note down the CID number of it.
Pocket pc side:
First make sure that your dialing location settings are correct. To check this,
Start > settings > dialing locations > dialing patterns > just type "G" for local dial, long distance and international patterns.
then the connection part,
Start > settings > connections > select new from the top dropdown box > type "net" as setting name > select modem > type "internet" as connection name > select "generic irda" as modem > set the baud rate to 57600 > press "advanced" button > press the "name servers" button and type the dns numbers that you will learn from your gsm operators' support > press ok > press next > type *99***CID# for the number (remember the CID of your t610 connection that you have just created. for example, if your CID is 5, the number to dial is *99***5# ) > press next > un check the "wait for a dial tone" then save and exit.
now you will be able to connect via infrared.
_________________
--Currently Using--
Ipaq 3950
Sony Ericsson T610
Flyjacket i3800
Flyjacket iCAM
512 mb Sandisk Ultra CF Card
1 gb Sandisk CF Card
256 mb Sandisk SD Card
[ This Message was edited by: BloodyRune on 2003-07-18 13:22 ]
--
Posted: 2003-07-18 14:20:06
Edit :
Quote
New Topic
Reply
