Sony Ericsson / Sony : Software, Firmware and Drivers : Raider camera driver for K790, K800 and K810 (v6.6.5)
>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> Raider camera driver for K790, K800 and K810 (v6.6.5)
Bookmark topic
whatever it is k800 does not take good landscape pictures.
well, you just can't compare picture which are not similar (time, scenery, lighting). your pictures aren't. on first from K800 you're trying to capture sky, on second ground but where is the sun? isn't it more towards the camera?
maybe it's not the champ but it can
--
Posted: 2008-08-03 10:51:08
Edit :
Quote
Raider 6.3.3
Hello >>>
Pic From......... Bangkok Thailand
Sony Ericsons
K790i Cyber Shot Phone
[ This Message was edited by: kongdotcom99 on 2008-08-03 11:31 ]
--
Posted: 2008-08-03 12:20:25
Edit :
Quote
@Raider, I really don't want to get on your back, but could you, please, do something with the autofocus in EM/SEM with/without flash? To me it doesn't allways work and it's a very annoying thing, because I'm a big fan of 6.3.3 and I love night shots.
--
Posted: 2008-08-03 12:35:09
Edit :
Quote
Raider 6.3.3
Raider 6.1.1
--
Posted: 2008-08-03 13:53:19
Edit :
Quote
On 2008-08-03 10:51:08, Raiderski wrote:
whatever it is k800 does not take good landscape pictures.
well, you just can't compare picture which are not similar (time, scenery, lighting). your pictures aren't. on first from K800 you're trying to capture sky, on second ground but where is the sun? isn't it more towards the camera?
Nice pictures. I think a little bit higher contrast ( +1) and saturation will improve the landscape pictures (just my opinion)
Raidersky, I would like to ask you for a favour. I have modded your driver so that I can have EM on/off in either Fine/Normal mode but I am struggling with 1 problem. I would like to turn BestPic into HDR mode. As we know that BestPic will take 9 pictures at the same time and allow us to save them seperately. Therefore, I would like to put some codes so that after every delay, the value of EV will be changed from -2.0,-1.0,0,1,2 or more. However, because of my lack of experience in I2C, so far I just realized that there is a limit in doing so (language and property_1d). If it is possible, please give me some advices or could you please spend some of your free time on this. Also, could you please send me any available instructions about I2C language. Thank you very much and best wishes to you
--
Posted: 2008-08-03 14:06:47
Edit :
Quote
at raider
nice pictures.but can it take good pictures as well as them in direct sunlight ? (not in cloudy sky)
--
Posted: 2008-08-03 17:30:32
Edit :
Quote
Here you are my OSD (in progress)
Its just a PNG
--
Posted: 2008-08-03 17:49:32
Edit :
Quote
raider wich settings did u used?
sacirxposed
nice
really nice
looks like pro.
other's are nice too.
--
Posted: 2008-08-03 19:42:14
Edit :
Quote
@sacirxposed
sooo nice and pro OSD!! Hope you share it when it's final.
--
Posted: 2008-08-03 20:33:35
Edit :
Quote
On 2008-08-03 17:49:32, sacirxposed wrote:
Here you are my OSD (in progress)
Its just a PNG
can you zip and send it again please ?
--
Posted: 2008-08-03 22:00:28
Edit :
Quote
New Topic
Reply
