>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
General
> Official SE C901 Cybershot discussion
Bookmark topic
thanks again dude.. but im not using jjpatcher... cuz my phone certificate is brown.... and ill use vkp patches can i possibly revert that patches?
--
Posted: 2010-05-20 14:59:46
Edit :
Quote
You need to use far manager with some plugin, scroll down page
http://forums.se-nse.net/topi[....]utorial-a2-permanent-patching/
You need a copy of your phoneapp first. By reverting do you mean removing patches you have put on? Answer is yes you can remove.
--
Posted: 2010-05-20 15:14:32
Edit :
Quote
hmnnn.. ok ill read that one.. thnk you so much
OFFTOPIC:
i wanna show this to you guys.. got bored a couple of hours ago = result ;p
[ This Message was edited by: macmigz on 2010-05-20 16:24 ]
--
Posted: 2010-05-20 17:20:15
Edit :
Quote
-offtopic-
haha that's one pimped c901!
Did you buy that or make it yourself?
It's disguised as a panda, you should dress up in a full size panda suit, then you'd be able to get close up photos of them
-offtopic-
I find the plastic of the battery cover and frame to be really slippery with not much grip, I need to make something a bit like that so i dont keep dropping it
[ This Message was edited by: mriley on 2010-05-20 17:19 ]
--
Posted: 2010-05-20 18:09:54
Edit :
Quote
OFf Topic:
haha.. thanks bro.. yep i did make this one.. made me busy for an hour....
i went to the mall to buy something then i drop by at a tech center..
that skin catched my attention cuz its a different from others its a sticker skin but the covering has coton like material i find it cute... my 2nd time using a skin on a gadget but 1st time putting it myself... i got my n70 way back skinned on a skinning center
--
Posted: 2010-05-20 18:44:51
Edit :
Quote
In recent days I tried Raider's and jigongx's modded camdrivers, but of course the auto-focus didn't worked fine with any of them. Now I'll share my experiences with theese drivers to see if is it possible that my hardware is faulty, or not...
First of all, with manual focus I can control the values between infinite and the closest distance, and is possible to get sharp pictures of almost any objects, but it isn't that simple.
In Raider's driver I experienced probably a very little slight "jump" when "zooming" at 1/3 of the zooming bar from the infinite point. Should it be so, or could it indicate some hardware fault?
With Jigonx's driver is more simple to get the result you want. There -for me, with manual focusing- the -2,0 is the infinite, the -1,3 is already for a distance below 1m. And the -1,0 value already for a macro distance. The closest position of the lens is at +1,0 -I checked the position of the lens on the back of the phone too. Do this driver's manual camera settings work in the same way for others, who tried it too? Is it possible that not the camdriver, but other part of the firware defines that the camdrivers certain value for a focusing distance to which lens position belongs? This would make sense, because in this context in Jigonx's driver for me between -1 and +1 are the makro distances -so nearly 2/3 of it's range defines a makro distance, and my pictures with auto-focus are focused closer than sould be.
The sports mode is the same, auto-focusing works almost normally. And -as I remember- with the first firmware the focusing worked fine also.
Please check if with your phone the manual focusing works the same way (with raider's and jigonx's driver too).
After theese is it possible that the hardware has faults? (As I wrote I can adjust manually the focusing distance quite well between infinite and the closest macro distance.) Anyway, the firmware should be faulty for sure, because if the hardware would have been faulty, and that would cause the wrong focused pictures, after the focusing process, when pictures are out of focus, it should indicate that the focusing isn't optimally done, not the opposite (that focusing is done).
--
Posted: 2010-05-21 10:50:41
Edit :
Quote
about flash sync during long shutter speed; Flash mode and how it affects the flash timing,
-Forced flash RER: front/leading curtain flash
-Auto flash: rear/trailing curtain flash
--
Posted: 2010-05-21 14:03:39
Edit :
Quote
hellp
why cant i patch my phone in a2uploader ive followed this instructions
1. Open A2 tool and in ‘MISC’ field browse for the .vkp patch you want.
2. Now click on ‘E’ there, the patch’s coding will open in notepad.
3. Add this line at the top in the beginning of the patch “;pAtChFiLe=/boot/phone_app.cxc” [without quotes]. Make sure that there is no spaces in it. May result in ACK error.
4. Save the file and close the notepad
5. Now click on Write script and connect the phone with ‘c‘ key pressed. If its your phone’s power button then use ‘2+5‘
6. Sit back and relax. A2 Uploader takes a long time. Even with small patches. When a popup comes up click “NO”.
7. After it says, “ELAPSED: xx secs.” it has ended, and you can unplug your phone.
but i cant do step 6 no popups happen it go start to step 7.... i have brown certificate already T_T
--
Posted: 2010-05-21 15:46:30
Edit :
Quote
Its better to use far+cxc plug-in than A2 Uploader and its fast.
--
Posted: 2010-05-21 15:59:07
Edit :
Quote
Yep, A2 Uploader method is really slow and probably wont work, Junz did a tutorial a few months ago that showed me how to do it
--
Posted: 2010-05-21 16:08:50
Edit :
Quote
New Topic
Reply
