Sony Ericsson / Sony : Software, Firmware and Drivers : first prototype (v2) of supermode camdriver for K790/K800/K810
>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> first prototype (v2) of supermode camdriver for K790/K800/K810
Bookmark topic
anyone tried this driver yet?????if someone has tried it can we have an opinion?
--
Posted: 2008-05-26 13:41:43
Edit :
Quote
@ Raider
any chances that the driver will be released by friday?I'm going on a trip and would like to use the new release
--
Posted: 2008-05-26 14:17:35
Edit :
Quote
On 2008-05-24 23:18:02, pietropizzi wrote:
This patch replaces the standard Zoombar image with an extended Supermode-Zoombar Image and the Stick is also replaced. It is shown as soon as one of the Zoom-Keys is pressed.
BUT I'd prefer NOT to patch this old one as it may not fit to the new driver which will be released.
okand when I change camdriver, the picture will be show forever? Or only with this raidersky camdriver?
--
Posted: 2008-05-26 19:07:01
Edit :
Quote
zoombar is replaced by this picture
--
Posted: 2008-05-26 19:14:08
Edit :
Quote
budala
i hope so. of course it's better to try out a new driver through a few days to familiarize with it and to avoid surprises (especially on the trip)
Mike2
2sec is not much, however main goal for me was to remove noise (using longer exposure time) that's why i'm quite satisfied
pietropizzi
1. ISO values on which EV ?
2. So shutter will still be fixed to ISO 100 ? "cannot be used together...
3. Are there "sub-steps" for each color in EV as I see only saturation has fixed EV position ?
1. right now i have ISO on +1.3 (zoom moved to +1.7) but of course you can change position as you wish (in code)
2. yes, i don't see possibility to combine manual shutter speed and manual ISO
3. yes of course. one color function have 30 steps. balance (two colors) have 15 steps for one color and 15 steps for second color. i didn't fixed them to any EV position right now because i'm not using them
--
Posted: 2008-05-27 10:22:24
Edit :
Quote
Raiderski
2. yes, i don't see possibility to combine manual shutter speed and manual ISO
You think it is better the two separate work shutter speed slow or shutter speed high and iso?
There will be difficult for users to know that iso relate to the shutter?
--
Posted: 2008-05-27 13:15:17
Edit :
Quote
On 2008-05-27 10:22:24, Raiderski wrote:
i don't see possibility to combine manual shutter speed and manual ISO
You mean to control them at the same time?
If I'm right the problem is that when we set ISO after shutter, the shutter is reseted. Can be possible to add a delay and put it togheter, but changing ISO first? I'll try to do some tests.
Also, the reseting problem can be fixed storing shutter value and restoring it after manual ISO setting.
[ This Message was edited by: jomateixa on 2008-05-27 18:33 ]
--
Posted: 2008-05-27 14:16:00
Edit :
Quote
yep, my fault. I didn't check this well - ISO and shutter speed can be used together. today I will try this also with AE lock
brazuka
fast and slow shutter speed is because of too much values for shutter speed (total 41 values, range 1/6400s - 2s) and 'only' 30 steps for function value
_________________
K800 R1KG001 (camdriver 6.1)
raider.4shared.com
flickr.com/photos/raiderek
[ This Message was edited by: Raiderski on 2008-05-27 14:28 ]
--
Posted: 2008-05-27 15:26:24
Edit :
Quote
Raiderski wrote: yep, my fault. I didn't check this well
.... couldn't even trust my eyes reading this....
--
Posted: 2008-05-27 15:37:06
Edit :
Quote
BTW. you can guys (any girls here?) take a look at my second post in this thread:
http://www.esato.com/board/viewtopic.php?topic=170105&start=105
I must to admit that photo with Short Enhanced Mode is this what my eyes saw
--
Posted: 2008-05-27 16:16:03
Edit :
Quote
New Topic
Reply
