Sony Ericsson / Sony : Software, Firmware and Drivers : Raider camera driver for K790, K800 and K810 (v6.6.5)
>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> Raider camera driver for K790, K800 and K810 (v6.6.5)
Bookmark topic
Thanks
--
Posted: 2009-04-20 15:08:57
Edit :
Quote
@Raiderski
hmm .. thankz buddy .. i think i got my answer
... i'll do it manually in that case
--
Posted: 2009-04-20 15:26:43
Edit :
Quote
no problem
mechexpert
easiest solution to make long exposure in dark light without any manual changes after the camera start is to enable permanent EM for 'normal quality' in the camera menu
E_MODE = 02
if necessary (low light) it will use EM mode and of course it will override normal quality to use fine quality settings
--
Posted: 2009-04-20 16:10:17
Edit :
Quote
On 2009-04-20 16:10:17, Raiderski wrote:
no problem
mechexpert
easiest solution to make long exposure in dark light without any manual changes after the camera start is to enable permanent EM for 'normal quality' in the camera menu
E_MODE = 02
if necessary (low light) it will use EM mode and of course it will override normal quality to use fine quality settings
i changed the {E_MODE= $s5 02;} in the cam driver. Now it means that i have to select normal quality to enable dis mode ?/ or do i have to do something else too ??
thankz
--
Posted: 2009-04-20 18:42:08
Edit :
Quote
$c0 03 $s0 1a // -2.0 AEB assistant
$cl $c0 04 $s0 05 // -1.7 Sharpness
$cl $c0 05 $s0 17 // -1.3 Balance orange - light blue
$cl $c0 06 $s0 18 // -1.0 Custom White Balance
$cl $c0 07 $s0 07 // -0.7 Contrast
$cl $c0 08 $s0 08 // -0.3 Colors saturation
$cl $c0 09 $s0 01 // 0.0 Focus
$cl $c0 0a $s0 09 // +0.3 Exposure compensation (EV)
$cl $c0 0b $s0 03 // +0.7 Shutter speed fast
$cl $c0 0c $s0 02 // +1.0 Shutter speed slow
$cl $c0 0d $s0 19 // +1.3 ISO sensitivity
$cl $c0 0e #ZM_TYPE // +1.7 Zoom
$cl $c0 0f $s0 0a // +2.0 Autoexposure lock
Dont mind but raiderski, can you help me with this please
AEB is in -2.0 and EV is in +3.0
so now i select AEB to step 1
then go to EV
but this doesn't work
I know i'm doing it wrong. but where ??
[ This Message was edited by: firoz3321 on 2009-04-20 17:49 ]
--
Posted: 2009-04-20 18:45:34
Edit :
Quote
Dont mind but raiderski, can you help me with this please
AEB is in -2.0 and EV is in +3.0
so now i select AEB to step 1
then go to EV
but this doesn't work
I know i'm doing it wrong. but where ??
may be i can help you firoz ... here is wt u have to do ...
select EV & set it to -2.0
now AEB & move to value +1
this combination will give you a total of 5 shots
hope u get it
--
Posted: 2009-04-20 18:54:07
Edit :
Quote
Color saturation Max .. Raider cam driver 6.6.3
--
Posted: 2009-04-20 19:03:34
Edit :
Quote
redirected to this topic from >>>>>>>>>
http://www.esato.com/board/viewtopic.php?topic=184600#post2648300
--
Posted: 2009-04-20 19:29:27
Edit :
Quote
RAIDER ---->
why do you use an old version of firmware... ???
any special reasons?
--
Posted: 2009-04-20 19:39:47
Edit :
Quote
mechexpert
yes, if you select 'normal quality' in the camera menu EM mode will be active all the time until you won't change it to 'fine quality'. remember that you don't have to disable EM in good light conditions, it won't be activated in good light
firoz3321
since v6.6.2 you don't have to use EV function at +0.3 to select initial EV compensation for AEBa. try this:
1. go to AEBa function (in your case at +2.0)
2. select step 1.0
this one is important:
move joystick left and right several times to see that it can change EV compensation like in stock driver
you have to use joystick to change initial EV compensation for AEBa, not a function at +0.3
if you'll set step 1.0 and initial EV to -2.0EV then you will get 5 shots
coolharsh55
no problems, no reason to change
--
Posted: 2009-04-20 20:17:32
Edit :
Quote
New Topic
Reply
