News Forum Phone database

> New Topic
> Reply
< Esato Forum Index > Sony Ericsson / Sony > Software, Firmware and Drivers > Modded Camera Driver for k800i/k810i Bookmark topic

Hey guys

I think this might be intresting to some of you : http://www.michaelalmond.com/Articles/noise9.htm most others might already know the power of this but's it's always nice to see a few good examples!
--
Posted: 2008-01-13 21:47:08
Edit : Quote


A question, im going to experiment a little with camdrivers, change some easy settings.
And what i wonder is, take contrast for an example, i have understod i change every (55,XX) in the driver to ex(55,01) and so on -
but what about the stuff writen beside it; // Reset contrast and sometimes // Reduced or // Increased.. ?

Do i have to change them to?

--
Posted: 2008-01-14 05:56:50
Edit : Quote




In the code the stuff next to "//" is taken as a comment.
--
Posted: 2008-01-14 13:58:40
Edit : Quote


increasing contrast, also by default increases the exposure, causing over exposure.
--
Posted: 2008-01-14 14:03:00
Edit : Quote




right
--
Posted: 2008-01-14 14:05:54
Edit : Quote


I did some mini tests comparing Genus 6.0 [06 Sharpness], ModMix 1.42, number1 2.95 and Ultimate 2.0 in document mode.

I found out that modmix, number1 and genus' driver can focus nearer object in document mode. But with ultimate 2.0, I can focus nearer. I'll upload the 4 pics later...comparing the minimum distance to get proper focus.

Ultimate 2.0 - http://img206.imageshack.us/img206/4153/ultimate2ao0.jpg

Genus 6.0 [06] - http://img115.imageshack.us/img115/3630/genus6yv3.jpg

number1 2.95 - http://img89.imageshack.us/img89/2715/number1295co5.jpg

ModMix 1.42 - http://img100.imageshack.us/img100/8068/modmix142dz2.jpg
--
Posted: 2008-01-14 16:00:37
Edit : Quote



So,what we can do to increase default contrast without increasing of default exposure or haw we can decrease default exposure and what are recommended values...?
Can we set something like:
#COM_EVENT(55,02)
#COM_EVENT(06,FE)
or
#COM_EVENT(06,FF)....?


..or if I`ll make this:
seq_set_prop_1_0 = #COM_EVENT(11,80);
seq_set_prop_1_1 = #COM_EVENT(11,80);
seq_set_prop_1_2 = #COM_EVENT(11,80);
seq_set_prop_1_3 = #COM_EVENT(11,80);
seq_set_prop_1_4 = #COM_EVENT(11,80);
seq_set_prop_1_5 = #COM_EVENT(11,80);
seq_set_prop_1_6 = #COM_EVENT(11,80);
seq_set_prop_1_7 = #COM_EVENT(11,80);
seq_set_prop_1_8 = #COM_EVENT(11,80);
....?

[ This Message was edited by: Goldmen on 2008-01-14 21:49 ]
--
Posted: 2008-01-14 16:07:32
Edit : Quote




What were the lighting conditions for these pictures? IMO the minimum focus distance is the same because its a hardware feature not a software one.
--
Posted: 2008-01-14 18:21:53
Edit : Quote




In Number1 driver (copied by you and genus) the fps shutter are decreased in low light condition. As the max time for autofocus remain the same, algorithm isn't able to set focus so near because objetive can't move the necessary distance before autofocus time is over. As far as I know it's the only logical explanation.

[ This Message was edited by: jomateixa on 2008-01-14 23:40 ]
--
Posted: 2008-01-14 23:05:17
Edit : Quote




You will f**k all the WB settings and won't be able to change it from phone menu I think
--
Posted: 2008-01-14 23:12:57
Edit : Quote

---

New Topic   Reply

Forum Index