>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> WotanServer
Bookmark topic
Davinci won't recognise it with a full battery
[ This Message was edited by: wolfboy21 on 2008-03-22 15:31 ]
--
Posted: 2008-03-22 16:31:03
Edit :
Quote
On 2008-03-22 16:31:03, wolfboy21 wrote:
Davinci won't recognise it with a full battery
[ This Message was edited by: wolfboy21 on 2008-03-22 15:31 ]
what about xs++?
--
Posted: 2008-03-22 16:48:51
Edit :
Quote
Ok, left the battery out for 15 mins and gave davinci a go.
IM Lock Staus: LOCKED
Identification Time - 00:00:32
Done!
Service Selection Started...
Getting Conversion Script From Server For: K800i / CID52 / Red...
SELECTED: Conversion For K800i To
Script Execution Started...
Checking Files...
Downloaded 62Kb In 1 sec
Downloaded 62Kb In 1 sec
Downloaded 62Kb In 1 sec
Starting up...
Script initialization. Please wait...
Disconnect The Phone, Reinsert Battery And Connect Again Holding 2+5 Keys...
Connected!
SEMCUSB 2+5 Mode Detected.
It gets to the above and just hangs. I'm trying to do an EROM update.
--
Posted: 2008-03-22 16:52:38
Edit :
Quote
just a thought have you checked your junk mail to see if they posted your login and password there?
--
Posted: 2008-03-22 16:53:01
Edit :
Quote
Yes nothing there i'm afraid.
What an earth is up with this thing
--
Posted: 2008-03-22 16:56:14
Edit :
Quote
Davinci still won't work, it just hangs on awaiting phone answer when trying to do an EROM update.
Is it the GDFS?
--
Posted: 2008-03-24 13:37:36
Edit :
Quote
On 2008-03-24 13:37:36, wolfboy21 wrote:
Davinci still won't work, it just hangs on awaiting phone answer when trying to do an EROM update.
Is it the GDFS?
have you tried pressing 2&5 (doesnt work with xs++, it hangs even on a fully working phone) instead of 'c'?
otherwise have you got a service cable?
--
Posted: 2008-03-24 13:50:25
Edit :
Quote
It gets upto the remove usb cable,remove battery,then re-insert battery and cable pressing 2+5.
I hold 2+5 and then it hangs on "waiting phone answer".
It's weird, one minute the computer cannot recognise the phone so I have to pop the battery out and leave it for a bit.
It'll then recognise it.
No, I don't have a service cable i'm afraid.
--
Posted: 2008-03-24 14:54:04
Edit :
Quote
On 2008-03-24 13:50:25, gaming_guy wrote:
On 2008-03-24 13:37:36, wolfboy21 wrote:
Davinci still won't work, it just hangs on awaiting phone answer when trying to do an EROM update.
Is it the GDFS?
have you tried pressing 2&5 (doesnt work with xs++, it hangs even on a fully working phone) instead of 'c'?
otherwise have you got a service cable?
I have just tried connecting to Davinci using 2+5 and I get the following :-
(#) DaVinci Service Client v22.35
New device connected on USBF3
Device Identification Started...
Checking Files...
SEMCUSB 2+5 Mode Detected. Use This Mode For Recovery Only!
Then at the bottom "waiting phone answer".
Soo annoying this is!!
--
Posted: 2008-03-24 14:58:02
Edit :
Quote
Tried to flash the main using SETool :-
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition - please visit
http://www.setool.net and buy FULL.
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:49 PAF:1 IMEI:3539 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
wrong response, break.
loader fs startup failed, that is fatal
Elapsed:254 secs.
[ This Message was edited by: wolfboy21 on 2008-03-24 14:13 ]
--
Posted: 2008-03-24 15:10:48
Edit :
Quote
New Topic
Reply
