News Forum Phone database

> New Topic
> Reply
< Esato Forum Index > Sony Ericsson / Sony > Technical > Everything regarding SE T230,T290i and cable connection here! Bookmark topic

Sure it's possible to send sms from pc, just use FMA.
--
Posted: 2004-07-19 11:27:12
Edit : Quote


@ ESTOR,
Well I tried using a friend's DSS-25 sync station that came with her P900 yet it didn't connect; I downloaded the driver from SE site and after installation my PC's device manager indicated that it is working well but the phone monitor did not recognise T230. The SE site listed T230 as one the compartible phones that works with DSS-25. I thereafter tried using Christersson's send file but it says: phone not connected. PLS HELP!!!!
--
Posted: 2004-07-20 21:49:37
Edit : Quote


I suggest you use float's mobile agent instead. much less headache.

To use SENDFILE or any SE software, you have to install and properly configure Mobile Phone Monitor (control panel -> Phone Monitor Options) and "enable" the COM port that corresponds to your cable/sync station.

[ This Message was edited by: ESTOR on 2004-07-20 22:38 ]
--
Posted: 2004-07-20 23:35:11
Edit : Quote


@ Estor,
Still did not connect even with FMA. I selected serial connection;the port where DSS-25 is connected to, yet no connection with phone. PLS HELP!!
--
Posted: 2004-07-22 20:24:31
Edit : Quote


The COM port speed for the cable must be set at 9600 for T230. If you are using SE software, you can do that by Device Manager -> Ports -> COMx -> Port Settings -> Bits per second

If you are using FMA, you can also set it within the program.
--
Posted: 2004-07-22 21:05:24
Edit : Quote


just lettin you all know, ive been a way for a while, but ive worked a few things out, and found a trick none of you have mentioned before.


ok, for those having problems, here is the quick way.

use fma, its easy to use, and has lots of tricks.
it seems no one has been able to use all the functions yet, but ive worked a way to use them all, including making phone calls, downloading and uploadin, sending sms, the lot.

ok, baud rate MUST be 9600, make sure none of the comm ports on your pc are being used by anything else,( so it can detect you cable connection easier, can turn them on later) and that fmais turned to comm 4. make sure the rts and dtr are on.

next, turn the irmcsync of(disable), otherwise it wont connect ( found this with all phones ive tried)

than go to connect ( i dont thinki missed anything)

ok, it should connect ok, but at this point you are limited to what you can do, no sms, no calls, and no uploads/downloads ( ive found)

here is that part no one has thought of, once it is connected, turn the irmcsync BACK ON...... this now allows everything to be used, sendin sms, making phone calls, downloadind AND uploading, the lot.

hope this has helped, letme know if it does

cheers

ghost

[ This Message was edited by: ghost&roser on 2004-07-23 16:15 ]
--
Posted: 2004-07-23 17:12:09
Edit : Quote


Everything works if irmcSync is turned off (except for downloading)...did you actually download any picture from your T230?
--
Posted: 2004-07-26 12:05:40
Edit : Quote


I concur. IrmcSync remains off and I can do everything on the phone.

In fact, the only thing that I had to change in FMA after installation is the speed being adjusted to 9600. Everything else I never touched.

[ This Message was edited by: ESTOR on 2004-07-26 20:15 ]
--
Posted: 2004-07-26 21:11:31
Edit : Quote


@ Estor,
Thanks man I followed your last suggestions and successfully connected to FMA. I was thereafter able to upload(according to FMA) images, ringtones etc to the phone. Thanks Again!
--
Posted: 2004-07-26 21:17:50
Edit : Quote


Wow!
I just used these tips to connect via my T230 via USB-cable.
After an hour of sweating I got it to work thanks to this forum!


Thank YOU!


--
Posted: 2004-07-28 14:39:06
Edit : Quote

---

New Topic   Reply

Forum Index