Sony Ericsson / Sony : Software, Firmware and Drivers : Hybrid Camera Driver for W800i/K750
>
New Topic
>
Topic Locked
Esato Forum Index
>
Sony Ericsson / Sony >
Software, Firmware and Drivers
> Hybrid Camera Driver for W800i/K750
Bookmark topic
Quote:
On 2006-11-09 02:21:25, jiji wrote:
ok ok
imje can you explain What is the diffrence between 2E and 1F?
//---------------------------------------------------------
//These two lines controls the locked frame rate in VR.
//Use them to test different settings!
//The value entered is the desired frame rate * 4.
//Example: 2E means 0x2E = 46 => frame rate 46 / 4 = 11.5 fps
// this is MACRO programming define and you must use it down instead of 2E end 1F
//it can work without macro , then will stay 2E and 1F.
//for 16fps you put 16*4=64=0x40 etc.
VR_NORMAL_MODE_FR=2E;
VR_NIGHT_MODE_FR=1F;
//---------------------------------------------------------
--
Posted: 2006-11-09 09:16:30
Edit :
Quote
Quote:
On 2006-11-09 09:08:30, ToryXX wrote:
gprsman if you don't have this 60...bla bla bla...you don't change it ...because is the same driver 0.85
Ok ToryXX grazie.
--
Posted: 2006-11-09 09:20:15
Edit :
Quote
Have you try to take a picture in dark using night mode? try 7.82...
If you use night mode and/or built it flash with V7.82, don't forget to set at least -1.00 for brightness...
I have try v7.82 and Tory's driver...but v7.82 is the winner for dark picture....sorry I can't upload the pictures...my admin block it.
--
Posted: 2006-11-09 09:38:16
Edit :
Quote
Quote:
On 2006-11-09 09:38:16, stingjoel wrote:
Have you try to take a picture in dark using night mode? try 7.82...
If you use night mode and/or built it flash with V7.82, don't forget to set at least -1.00 for brightness...
I have try v7.82 and Tory's driver...but v7.82 is the winner for dark picture....sorry I can't upload the pictures...my admin block it.
I confirm dark in 7.82 but put better photo to better fire in 0.85
--
Posted: 2006-11-09 09:45:31
Edit :
Quote
@ ToryXX
Please To correct dark zones disturbed also in sides as 7.82 and then are the best one with fire than 0.85...
--
Posted: 2006-11-09 09:49:20
Edit :
Quote
Quote:
On 2006-11-09 09:49:20, gprsman wrote:
@ ToryXX
Please To correct dark zones disturbed also in sides as 7.82 and then are the best one with fire than 0.85...
you want to enable the Spot????...because 7.82 is with spot enabled...tell me if you want this and i give you the driver privat!
--
Posted: 2006-11-09 10:23:53
Edit :
Quote
I want your driver (spot enabled) too Tory, it's better if you post in here...I am sure many ppl will glad to get yours
[ This Message was edited by: stingjoel on 2006-11-09 10:07 ]
--
Posted: 2006-11-09 10:28:25
Edit :
Quote
Quote:
On 2006-11-09 10:23:53, ToryXX wrote:
Quote:
On 2006-11-09 09:49:20, gprsman wrote:
@ ToryXX
Please To correct dark zones disturbed also in sides as 7.82 and then are the best one with fire than 0.85...
you want to enable the Spot????...because 7.82 is with spot enabled...tell me if you want this and i give you the driver privat!
Yes thanks
--
Posted: 2006-11-09 11:05:33
Edit :
Quote
Quote:
On 2006-11-09 10:23:53, ToryXX wrote:
Quote:
On 2006-11-09 09:49:20, gprsman wrote:
@ ToryXX
Please To correct dark zones disturbed also in sides as 7.82 and then are the best one with fire than 0.85...
you want to enable the Spot????...because 7.82 is with spot enabled...tell me if you want this and i give you the driver privat!
Yes thanks ,
Not touched put to focus is the best; -)
[ This Message was edited by: gprsman on 2006-11-09 10:11 ]
--
Posted: 2006-11-09 11:11:03
Edit :
Quote
Quote:
On 2006-11-09 09:16:30, imsje wrote:
Quote:
On 2006-11-09 02:21:25, jiji wrote:
ok ok
imje can you explain What is the diffrence between 2E and 1F?
//---------------------------------------------------------
//These two lines controls the locked frame rate in VR.
//Use them to test different settings!
//The value entered is the desired frame rate * 4.
//Example: 2E means 0x2E = 46 => frame rate 46 / 4 = 11.5 fps
// this is MACRO programming define and you must use it down instead of 2E end 1F
//it can work without macro , then will stay 2E and 1F.
//for 16fps you put 16*4=64=0x40 etc.
VR_NORMAL_MODE_FR=2E;
VR_NIGHT_MODE_FR=1F;
//---------------------------------------------------------
Imje man,
I'm convinced that your interpretation is out of context.. and I'm not sure that you understand driver correctly. Take Andeo link to Russian I2C and camdriver explanations.. and read it very very careful. I think you'll change the idea.
Macro is hard coded in OS and it's a small part of the driver who tell the default info to adapt after zoom, focus and aperture.
And for video.. i think (and it's my opinion only) that you got it totally wrong, man. All you have to do is to use Calculator from XP-Accesories with Scientific part.. and to multiply like this:
Y fps * 4 = X and then X to be converted to Hex. => Z number... wich can be 44=17; 40= blabbla .....
I think you have to review the documents once again.. because i saw that you want to make a driver part by part... but.. even so... you have to know whatyou coppy and what not to... Am I wright?
I don't want to offend you or smt.. but ... you have to understand that everything posted here is like a stone in deep water: Make waves. Be carefull, please.
thanks for understanding.
--
Posted: 2006-11-09 12:50:27
Edit :
Quote
New Topic
Topic Locked
