>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
General
> plz solve this problem
Bookmark topic
i am having k750i and i have used far manager to get into my fones directory i connected my dcu and followed instructions but when i get in my FS so its blank and nothing is there.
plz help me what can i do in this condition.
--
Posted: 2006-07-03 01:13:25
Edit :
Quote
I found this happens sometimes. Exit Far cleanly, turn off your phone, remove the battery, put battery back in and try again
--
Posted: 2006-07-03 01:19:07
Edit :
Quote
i have tried this thing many times but i found no solution yet
--
Posted: 2006-07-03 02:07:46
Edit :
Quote
Reinstall the plug in..
--
Posted: 2006-07-03 04:15:00
Edit :
Quote
I found this problem as well. The way I was able to get around it was to lower the baud rate on the connection. I put it to 115kbps to guarantee a connection but you can play around with the settings until you get a consistent connection.
--
Posted: 2006-07-03 04:18:01
Edit :
Quote
can you provide me with correct plugin and instructions on how to install it.
i have uninstalled every thing from my pc and now i want to do every thing from the beginning.
--
Posted: 2006-07-03 18:36:46
Edit :
Quote
sorry to be off da topic
can i use farmanager to access my j300i files
it tat software costly
--
Posted: 2006-07-03 19:00:51
Edit :
Quote
Quote:
On 2006-07-03 19:00:51, aragorn666 wrote:
sorry to be off da topic
can i use farmanager to access my j300i files
it tat software costly
SW is free!
details and questions are better placed in one of the following threats (SE-NSE Forum), because this is the board of the developers.
http://forums.se-nse.net/index.php?showtopic=3666
or
http://forums.se-nse.net/index.php?showtopic=3813
But now the bad news for you:
At this moment we can:
-read files
-write files
-move\delete files
-create folders
-delete folders
We can't (yet):
-rename
Phone models supported:
-k300/k500/k700/S700
-k750/w800/w550 CID36
-k600, z800 (works ONLY with service cable)
latest stable Version is 0.7.0.32
j300i isn't supported yet. If J300i is CID higher than 36 (don't know) it will take a lot of time, untill it is supported. CID means the security level and as higher the internal phone firmware is protected, as longer (if ever) it will take to give support.
back to topic:
Which version of SEFP-plugin do you use?
Version 0.7.0.32 should work without empty folder problems, if your phone is NOT CID49, if it's CID49 SEFP won't work. (reason, see above)
--
Posted: 2006-07-03 19:19:54
Edit :
Quote
I think its a problem with the DCU-60 cable, it dosent connect properly sometimes
Make sure the fone is on a solid surface, and dont move the fone when connected to FAR
--
Posted: 2006-07-03 19:28:57
Edit :
Quote
i used to put my fone on strong surface. apart from this i applied very much methods but was unable to connect.
look, first i used to start far plugin and then i click on 'n' located on top left corner and then i used to take out the battery of my fone and sim then i again put the battery after that i hold down 'c' and connect cable and at that moment i also used to click enter the matrix.
i used these plugins but found no result:-
SEFP06098
SEFP010251
if i am using the wrong plugin so plz tell me about right one
and plzplzplz solve my problem i will be very grateful of you
--
Posted: 2006-07-04 11:19:53
Edit :
Quote
New Topic
Reply
