>
New Topic
>
Reply<
Esato Forum Index
>
Sony Ericsson / Sony >
Symbian phones
> p900 case replacement
Bookmark topic
is the anyway to completely replace the p900 casing?, cause i hate the scratches.
thanks for any help.
--
Posted: 2004-05-07 22:09:05
Edit :
Quote
Is
this what you are looking for?
--
Posted: 2004-05-07 23:01:58
Edit :
Quote
thanks loads do they ship to the uk and how much it cost?
--
Posted: 2004-05-07 23:16:16
Edit :
Quote
They do ship to the UK...I received mine this morning.... took an hour of very careful transfering of all the inside components to the new case....
It cost $62.75 including shipping....
I ordered mine on 30th April....and as I said...arrived this morning....
--
Posted: 2004-05-07 23:27:06
Edit :
Quote
Quote:
On 2004-05-07 23:27:06, smilerthecheshirecat wrote:
They do ship to the UK...I received mine this morning.... took an hour of very careful transfering of all the inside components to the new case....
It cost $62.75 including shipping....
I ordered mine on 30th April....and as I said...arrived this morning....
Dear Sir do you have some instructions how to dissasemble the P900 for the Case Replacement, I want to avoid any mistakes or error, I think it is a very dificult process, please your help, thanks
Bdo
--
Posted: 2004-06-03 20:15:46
Edit :
Quote
Hello my friend....
Sorry I do not have any instructions.... I did it my self step by step...
It can be done using the small screw driver you get with your P900....
First take off your key pad....
Then the rubber stops at the back of your phone near camera lens....remove them and unscrew the screws that they hides.....
Remove battery cover and battery....
In battery compartment....there are two screws at the lower end...remove these....they are same length as the screws under the rubber stops....
Then you need something like a credit card...to slide between the top casing and the lower casing....and carefully....run it around...this will unclip it....
You will see wires dangling....these are for screen....you can unplug that....and underneath the screen is a metal shroud....that acts like a heat sink i think.....but you can unscrew that.....
Then I recommend....removing each piece one at a time...and fit it into the same postion of your new case.... Everything should just clip out quite easily....and clip back into the new case just as easy.....do not be tempted to remove everything....one at a time...
One thing worth noting...when you remove the speaker and microphone....do not forget about the foam shroud underneath them....as they were not with my new case......
Slowly and surely....and you will do it....I did find pluging the screen back when i had added the metal shroud and fitting the top cover to screen a little fiddly....but you can do it....hope this helps...
--
Posted: 2004-06-03 22:18:08
Edit :
Quote
i came across a posting recently about the keypad replacement. unfortunately i did not save it and now unable to find it via search.
would someone please provide the link again. i believe this site was selling the keypad for US$29.99
thanks!!
--
Posted: 2004-06-03 22:20:56
Edit :
Quote
You can find the P900 keypad part here:
http://www.globalmob.com/cart/customer/home.php?cat=75
Quote:
On 2004-06-03 22:20:56, sfaguy wrote:
i came across a posting recently about the keypad replacement. unfortunately i did not save it and now unable to find it via search.
would someone please provide the link again. i believe this site was selling the keypad for US$29.99
thanks!!
--
Posted: 2004-06-17 02:45:20
Edit :
Quote
if you look at the postal options on the global mob you can select the free posting option to UK via USPS Priority shiping.
--
Posted: 2004-06-17 13:45:06
Edit :
Quote
these look quite good :-)
This message was posted from a P900
--
Posted: 2004-07-27 17:21:16
Edit :
Quote
New Topic
Reply
