Esato Forums - Sony Ericsson / Sony : Software, Firmware and Drivers : K700i Repair ("Dead Phone detected!")

Index Menu

> New Topic
> Reply
< Esato Forum Index > Sony Ericsson / Sony > Software, Firmware and Drivers > K700i Repair ("Dead Phone detected!") Bookmark topic

Page12 >

afv Posts: 3

Hi, I flashed my K700i with last firmware (R2AE033) using davinci and then the phone worked about 5 minutes but after that, the screen started flashing white.

Now, when I try "Read CID", it says:

Client Version 12.5
**** READING CID STARTED ****
Power on the phone!
Detected SonyEricsson: K700/F500/K500/S700/Z500.
Dead Phone detected!
Recovering process started!
Status Ok, OTP Close, CID29, PAF1
IMEI: xxxxxx-xx-xxxxxx
Flashing 1 blocks...
address: 00000000, block: 1/1
Last sub block not accepted
SSW header not accepted!
SSW header not accepted!
SSW header not accepted!
Flash Loader not accepted
Execution Time - 00:03:52
Done!

What should I do?

[ This Message was edited by: afv on 2005-03-09 16:58 ]
--
Posted: 2005-03-09 17:34:28
Edit : Quote

hohohong Posts: 6

Same thing happen to me when I update software at SE website! I have the DSS-25 stand,... after completed, it started flashing white screen!!

Help
--
Posted: 2005-03-11 09:09:46
Edit : Quote

vineet_d Posts: > 500

U must go to the authorised service center and get it reflashed.....this should solve the problem.
--
Posted: 2005-03-11 09:53:21
Edit : Quote

hohohong Posts: 6

I can't reflash from SEUS? with DSS-25 stand? Thanks for you reply.
--
Posted: 2005-03-11 09:59:30
Edit : Quote

govigov Posts: > 500

Quote:
On 2005-03-11 09:59:30, hohohong wrote:
I can't reflash from SEUS? with DSS-25 stand? Thanks for you reply.

there is a repair/restore something in that site, you might want to try that.
--
Posted: 2005-03-11 11:25:33
Edit : Quote

whizkidd Posts: > 500

Haven't you got any service centre near you? This message was posted from a T230
--
Posted: 2005-03-11 11:32:29
Edit : Quote

Sebby Posts: > 500

Suggesting a service centre is no good as the phone has been flashed using DaVinci, which theoretically voids the warranty.

I'm sure DaVinci has a method of doing a full re-flash. I know SE Tool does. Contact the DaVinci team and explain the problem, and I'm sure they'll tell you the answer.
--
Posted: 2005-03-11 13:30:24
Edit : Quote

HyperiaBlue Posts: 424

Maybe you could try using SE tool to recover it...but of that i am not sure.
--
Posted: 2005-03-11 13:39:04
Edit : Quote

hohohong Posts: 6

I tried using SE tool to recover,.... but still the same thing!

I don't think there's SE service center new by. I bought this K700 online. K700 is not even officially introduce in my city.
--
Posted: 2005-03-11 16:49:16
Edit : Quote

HyperiaBlue Posts: 424

I suggest the following then:

Get yourself a DSS-25 synchstation, load the drivers onto your pc and then try to use SEUS (

's update service) but select recovery mode when you are about to flash it. The service should be albe to recover your dead phone.

Here is the link to SEUS:

http://www.sonyericsson.com/s[....]7_x&zone=ps&lm=ps1_1&pid=10139

Give it a try...it may just work.

_________________

Sony Ericsson - the marriage of the consumer electronics Beauty to the telecomms Beast

[ This Message was edited by: HyperiaBlue on 2005-03-11 15:57 ]
--
Posted: 2005-03-11 16:57:12
Edit : Quote

Page12 >

New Topic Reply